GC Gold Label 9 High Strength Posterior Restorative GIC 15 G

GC Gold Label 9 is the easy-to-use, handle and place fluoride-releasing alternative to expensive compomers and composites and in many cases, amalgam. It cures extremely hard and is very wear resistant. As a true glass ionomer, it chemically bonds to tooth structure, has a tooth-like coefficient of thermal expansion and releases significant levels of rechargeable fluoride. It's the perfect product for geriatric and paediatric restorations, final restorations (non-stress bearing areas), Intermediate Restorative (IRM), core material and long-term, temporary restorations.

1. POWDER AND LIQUID DISPENSING The standard powder-to-liquid ratio is 3.4g/ 1.0g. (1 level scoop of powder to 1 drop of liquid). For accurate dispensing of powder, lightly tap the bottle against the hand. Do not shake or invert. To dispense the correct amount of liquid from the bottle turn the bottle upside down, keep the nozzle away from the mixing pad and gently press the bottle. Discard the first 1-2 drops after opening a new bottle as the dispensed amount may not be accurate. Close bottles tightly immediately after use. 2. MIXING Dispense powder and liquid onto the pad. Using the plastic spatula, divide the powder into 2 equal parts. Mix the first portion with all the liquid for 10 seconds. Incorporate the remaining portion and mix the whole thoroughly for 15-20 seconds (Fig. 1). 3. RESTORATIVE TECHNIQUE Prepare the tooth using standard techniques. Extensive mechanical retention is not necessary. For pulp capping, use calcium hydroxide. Apply GC CAVITY CONDITIONER (10 seconds) or GC DENTIN CONDITIONER (20 seconds) to the bonding surfaces using a cotton pellet or sponge (Fig. 2). Refer to the respective instructions for use. Rinse thoroughly with water. Dry by blotting with a cotton pellet or gently blowing with an air syringe. DO NOT DESICCATE. The best results are obtained when prepared surfaces appear moist (glistening) (Fig. 3). Mix the required amount of GC Gold Label IX GP-EXTRA. Working time is 2 minutes from the start of mixing at 23°C (73.4°F). Higher temperatures will shorten working time. Transfer cement to the preparation using a syringe or other suitable instrument. Avoid air bubbles. From the preliminary contour and cover with a matrix if required (Fig. 4). g) When set, immediately apply GC Fuji VARNISH (blow dry) or GC Fuji COAT LC (light cure for 10 sec.). 4. FINISHING Final finishing under water spray using standard techniques can begin at 6 minutes after starting the mix. Apply a final coat of G-COAT PLUS and light cure for 20 sec. (Fig.5, 6). Alternatively, apply GC Fuji VARNISH (blow dry) or GC Fuji COAT LC (light cure for 10 sec.) Instruct the patient not to apply pressure for 1 hour.

Chemical adhesion to tooth structure allows minimal cavity preparation without the need for etching or bonding agents A chemical setting without shrinkage allows single-step placement without layering Similar thermal expansion as tooth structure produces minimal stress on the marginal seal Strontium-based glass provides good radiopacity and snap-set characteristics unanimously preferred by clinicians Strontium based fluoride-releasing formulation contributes to internal remineralization within tooth structure as well as increasing surface strength over time High compressive and flexural strength, and 60% higher wear resistance than conventional glass ionomers make Gold Label 9 strong enough for use in posterior teeth

Gc Gold Label 9 Extra - Big Pkg: 1 x 15 g Powder 1 x 8 g Liquid(6.4ml) Gc Gold Label 9 - Big Pkg: 1 x 15 g Powder 1 x 13.1 g (10.5mL)Liquid Gc Gold Label 9 Extra - Mini Pack: 1 x 5g Powder 1 x 3g Liquid(2.4ml) Gc Gold Label 9 - Mini Pack: 1 x 5 g Powder 1 x 5 g Liquid(4ml)

1.Service and Warranty are handled by the manufacturer/importer directly for this product 2. Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and meddent.in may assist the customer in registering a request to get the Product replaced or serviced. 3.meddent.in will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer 4.The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact or not altered in any manner or is not tampered as the case may be.