Prevest DenPro OraTemp C&B Temporary Crown & Bridge Material – 67g Automix Cartridge

Preparatory Work : 1.Take an alginate, silicone, or polyether impression from the intact row of teeth. Instead of an impression, a laboratory-made vacuum-formed template or, for single crowns, a preformed crown can be used for shaping. 2. To enhance the strength of the temporary restoration, remove interproximal grooves in the impression. If required due to tight spacing conditions, enlarge the relevant sites by cutting. 3. For easy replacement in the mouth, relieve undercuts. 4. With missing teeth or gaps in the molar area, cut a groove into the impression to produce a stable, bar-shaped connection in the temporary restoration. Initial Dosing : Remove and discard the cartridge lid. Under no circumstances should the cartridge lid be used to reseal the cartridge as this could result in the inclusion of air bubbles. Check whether both cartridge openings are free from obstruction and remove obstructing material, if any, with a suitable instrument. Before a mixing tip is applied for the first time, squeeze paste out onto a mixing pad until the base and catalyst pastes are at the same level. Discard the paste which has been squeezed out. Application : It takes the material a certain amount of time to emerge from the newly attached mixing tip. The flow of material is interrupted as soon as the pressure on the handle is reduced. Material that has set inside the mixing tip should not be extruded by force, as this may damage both the cartridge and the mixing tip. Core build-ups which are fabricated using composites, compomers, or resin modified glasionomer cements must be sealed off before the application of OraTemp C&B e.g., using Vaseline. ♦ First, install a new mixing tip. ♦ Prior to each application, extrude a small (pea-sized) amount of paste from the mixing tip onto a mixing pad and discard this material. ♦ Subsequently load the dried impression or vacuum-formed template in the relevant spaces from the bottom up. *Reposition the impression or vacuum-formed template in the mouth/on the model. ♦ The material attains a hard-elastic consistency within 1 min 40 sec after the onset of mixing. The material and the impression or vacuum-formed template must be removed from the mouth/model within 2 min 50 sec after the onset of mixing. ♦ Check the setting process by observing the excess material in the mouth or on the matrix/model. ♦ Keep the filled mixing tip on the cartridge to serve as a closure until the next use. Finishing : Completely remove the oxygen inhibition layer using alcohol (e.g., ethanol) once the material is completely cured (not earlier than 5 minutes after the onset of mixing). Polish if desired, e.g., with Sof-Lex™ polishing disks. After the product has cured completely, remove any residues. If necessary, finish and polish the temporary restoration using fine carbide burs. Do not breathe polishing dust. Use mouth protective device, safety glasses and aspiration. Cementation : Insert the temporary restoration with a commercial temporary cement, OraTemp NE. Eugenol containing cements may impair the setting of composite luting cements to be used at a later time in the final luting step! If a composite cement is to be used for the final luting step, seat the temporary restoration with a eugenol-free cement. After cementation thoroughly examine and explore the sulcus and surrounding dentition. Remove any residuals of the temporary material or cement from the mouth.

Excellent strength and low wear for durable temporaries. Superior Surface details. 1:1 Volume ratio for an even flow and improved handling properties. Low shrinkage and low curing temperature. Can be easily repaired with flowable composite. Extremely Polishable and colour stable.

1 x 67 gm Base/catalyst paste 1 x 16 Applicator tips 1 x 1 Instruction manual

02/12/2027

1.Service and Warranty are handled by the manufacturer/importer directly for this product 2. Any or all claims in relation to returns and replacement shall be made to the concerned Manufacturer/Importer only and meddent.in may assist the customer in registering a request to get the Product replaced or serviced. 3.meddent.in will not be liable to replace the Products and the liability to replace any such Product is that of the Manufacturer/Importer 4.The Buyer acknowledges that the Products once sold will not be exchanged or taken back unless the seal of the package or the Product is intact or not altered in any manner or is not tampered as the case may be